Submersible vibration pump for well. Reliable assistant in the country - Vibrating Pump Aquarius: Specifications and advantages of using the principle of operation of the vibration pump

Despite the large disputes regarding the reliability and feasibility of installing vibrational models, the Pumps of Aquarius have consistently occupy their niche in the list of popular, budgetary, practical, lungs in the installation and use of models.

Application and model

"Aquarius" applies:

to raise water from open sources (rivers, ponds, lakes of artificial water bodies), as well as tanks with a limited diameter (tanks, tanks);
for pumping fluid from basements, tranches, butt;
for the fence of drinking water from wells;
for watering plots of small area.

The pump is produced in three modifications: alifical, orion and poseidon.

Models differ in their technical specifications:

nominal and maximum volume of water supply;
power consumption;
sizes (height and diameter);
nominal pressure;
the number of valves (the more their number, there may be a large water supply).

The most powerful in its category is the BV-0,16-63-U5 Poseidon model. The power of the apparatus is 230W, water supply from 580 to 2000 l / h. Models in 2 valve are popular (although there are four valve). The pump is capable of lifting water to a height of 30-80 m.

Features of operation

The pump refers to submersible mechanisms for pumping fluid, that is, the device is placed below the water mirror, in the depth of the reservoir, tanks, trenches.

If the water layer is less, or the device is too close to the bottom - the quality of the pumped liquid is worsening, it becomes muddy, as the particles of sludge, soil, sand from the bottom come to a weighted state. Small particles are absorbed and rising with water.

Moreover, the mechanism of the vibration pump raises not only small particles, but also quite large pieces of soil, which are not absorbed by the filter, but settle at the bottom of the well, the bottom of the well is "stuck", the productivity of the aquifer decreases.

Therefore, the normal and long-term work of the vibration pump is possible if the well is drilled in a ground with large sand, stone fractions.

Small-grained sand, sooner or later, will score the filter of the pump or, penetrating the inside, disabling the mechanism.

Vibration pumps are used in wells. The peculiarity of the pump is reflected in the title. However, vibrations affect not only the work of the mechanism itself (everything that vibrates is faster than wearing), but also on the casing.

Profession of a specialist: Vibrating pumps are often targeted at the first stages of well pumping, for collecting dirty water wells.

Vibration affects the connection points of the mechanism details. Piston fastenings, valves are quickly promoted. Therefore, in these places, some masters immediately replace ordinary nuts on self-locking.

Dignity

The main pluses of vibro-pumps Aquarius can be attributed:

Relatively low price.
Easy to use. The mechanism does not require frequent parsing, lubricating parts.
The mechanism is located in the depths of the aqueous space, completely washed by a layer of water. That is, water becomes a natural cooling component of the system.
Details of the pump do not react to alkaline water indicators. They do not form a salt flaw.
The temperature of the pump is practically no affects the ambient temperature.
Compact, small.
The device can be used in narrow wells and pipelines from 100 mm in diameter.
If necessary, it is easily dismantled.

The most powerful pump series BV-0.16-63-U5 Poseidon (2 valves) has a hermetic case that prevents water inwards inside the mechanism. Cover coating protective and decorative.

Decorative and protective properties The coating will acquire thanks to the used powder painting technology by electrophoresis. Application of layer of powder polymers contributes to:

an increase in the duration of the pump and its reliability;
increase resistance with long-term interaction of the mechanism and water.

In order to prevent overheating of the mechanism, the pump compound is complemented by protective automation. Overheating may occur as a result of reducing the water level and the work of the mechanism "dry". So that the pump has burned enough 10-30 seconds of idle mode (if the thermal protection is not installed).

However, with the successful quality of the soil, subject to the safety and normal operation (alternation of active water intake - 120 minutes and time for cooling the mechanism - 15 minutes) - the vibration pump will serve at least 5-8 years.

See the video, which shows the principle of operation of the vibration water pump, relevant to the vibration pumps of Aquarius:

In the market of electric pumps under the Aquarius brand, the products of Ukrainian production of the Kharkov Plant Proelectro are presented. These are centrifugal submersible electric pumps (BCPE) for wells and only three types of household vibration models (BV ALIFIA, Orion and Poseidon). The small line of vibration models with the brand Aquarius replenishes the Russian manufacturer. Electromachine-building plant Lepse from Kirov produces a vibratory submersible pump of Aquarius 3 with an original appearance of a patented design designed for use in the household.

Fig.1 Pump Aquarius 3 - Appearance

Vibrating Aquarius Pump (BV-0,12-40) is designed to lift water from wells and wells, filling the water of pools, ponds, barrels and other tanks, drainage.

The household electric pump of Aquarius-3 has a standard design of vibration models - water absorption into the housing is performed when the rubber piston is vibrated, fixed on the pulley anchor of the electromagnetic coil. The piston vibrates with a frequency of 100 times per second, during its return movement occurs, the water is taken, and in prigly movement, the liquid is pushed out through the outlet of the electric pump.

The lower water intake part of the vibration pump housing is made of plastic, and rubber parts that come into contact with water have a natural rubber base.

Fig.2 Constructive device Aquarius 3

The main parameters of Aquarius-3

The electric pump is designed for the lower fence of drinking water and work in a vertical position, the main technical characteristics of the device are as follows:

The nominal pressure is 40 meters.
The depth of immersion under water mirror does not exceed 1 meter.
The temperature of the pumped fluid should not exceed 35 s;
The operating voltage of the device is 198 - 242 V. When working with reduced supply voltage wear of rubber parts of the electric pump decreases, which increases its service life. But it should be borne in mind that at low voltage, the nominal pressure drops to 20 meters.
The maximum feed volume is 1 m. Cube. / H, when working at a depth of 40 meters, the volume of the pumped liquid is 0.432 m.Kub. / H.
Pump has a class I protection (with grounding wire) from electric shock and built-in breaker, disconnecting the power supply of the electric pump while increasing the winding temperature (overheating protection).
The length of the electrical cord depending on the modification is 12 - 16 - 25 - 40 meters.
When the device is immersed in the well, its inner diameter should not be less than 100 mm.
The device is not provided for long-term operation - after 2 hours it is necessary to make a 15-minute break in its operation.

Fig. 3 Basic Aquarius Pump Knots 3: Electromagnetic Coil, Vibration System, Check Valve

Installation of Aquarius-3 to the source of water intake

The well household vibration pump BV-0,12-40 is completed with a protective ring, clamping for fastening the hose and deep holders for connecting the cord, cable and hose in an amount corresponding to the length of the electrical cable. For convenience, the pump is equipped with a watering nozzle and a transitional universal fitting. When placing a device in a water intake source, follow the following rules:

Fig. 5 Installation scheme BV-0,12-40 Aquarius in a water intake source

The electric pumps of Aquarius-3, produced by the Aviation Plant Lepse, refer to a number of budget devices (the average price of about 30 cu) and have low pressure indicators and water supply. Devices are not designed for a long time of continuous operation and can be used for watering or other work with the supply of small volumes of liquids under the supervision and manual control.

The number of water wells in our country is constantly increasing, which means that the demand for household submersible pumps is constantly increasing. The most popular type in this classification are vibration devices. The exhaust manufacturing technology was laid in the second half of the 20th century. This year, about 1 million pieces arrived at the counters, although the market is not limited to this amount. In such an abundance, it is difficult to understand on your own, what kind of vibration pump is better.

One of the most famous names, such devices are "baby" and "Spring". However, recently the model range has expanded significantly at the expense of local producers and representatives of Chinese business.

Hydraulics for the well

Choosing, what better the well pump for specific conditions, it is necessary to take into account a number of important operational factors:

the geometric and physical parameters of the well are taken into account;
the required amount of water for use in the country or in a private house;
not the last role plays the value on the price tag for the acquired instance.

When choosing a pricing policy, it is worth considering not only the payment of one pump, and the total price is the pumping station for the well, including trunk wiring from the pipeline. The kit includes both homemade water supply and fluid supply to sheds with homework, as well as wiring on watering garden crops.

It is advisable to take care of the presence of a spare cumulative water tank, as well as maximum system automation. This module will reduce the effect of hydrowards in the system, and will also allow the necessary pressure in the pipes at 2.5-3 atm.

Design of vibronasos

Submersible vibration pump has a simple design. At the same time, it does not need any additional service, such as regular lubrication or mandatory prophylactic work.

The apparatus is based on several important modules:

electromagnet;
vibrator;
sealed housing.

The electromagnet is a metal core of steel, as well as connected to a serial chain of coils. The core is made as a P-shaped. It is made up of a plurality of sheet plates of the same form.

There is also a working membrane that provides an additional fixation of the workbank. It mounted a pair of check valves to continue water.

Video: Review and repair of the vibration pump

Application of vibronic pump in the well

Operate the vibration pump in the well can be at any convenient depth. It should be noted that vibration is capable of reflected in the surrounding space. When the channel was done in stable rocks, for example, in sandstone, clay rocks or rocky soil, then no complications are boring.

But if the soil instability is observed, the layers of rock flooders are seen, the vibration is capable of a slightly torturing water. To further use the liquid, you will need to use various filters. Excessive vibration can even contribute to the clogging of the channels, which will negatively affect the influx.

Positive quality that promotes the purchase of vibroonasos is its small price tag. However, if at first the owner of the water pipeline is comfortable, then you often pay attention to the use of pumping stations.

Additional electrobatic

If the pump in the well for water supply at home is vibration, then it is recommended to mount an electrical stabilizer before connecting it. The electrical appliance balanced the supply of voltage on weak electroles. The need for a stable current value is that during the start the pump is forced to consume a high starting current.

Also during the work "Kid" or "Spring" will be given a guaranteed pressure when maintaining voltage at one level. Any stabilizer is able to extend the use of the pump, because manufacturers calculate their characteristics precisely from stable voltage values, current and frequency forces.

Choice between models

When the owner of the country house was determined with the type of machine, it remains to choose which vibration pump is better according to the model. For this, the corresponding search criteria are selected.

Performance

The value determines the amount of water pumped per hour. Allocate three groups:

minimum - up to 350 l / h;
average - 750 l / h;
powerful 1500 l / h or more.

Productivity is correlated with the debit of water. Do not take the extremely powerful, capable of pumping all the water in a few minutes, and then you have to wait for it again.

Pod

The indicator is relevant for the significant remoteness of the consumer's object from the point of water intake. The division is:

minimum for pumps is 40 meters of the water column;
a sufficient average value of 60 m;
maximum for household appliances up to 90 m.

It is worth considering that the pressure is not excessive, since about 20% on the loss should be discharged. With a horizontal arrangement, the remoteness of 10 m is equal to 1 m dive.

Water fence

There are two large types of the fence, one pulls the water from below, and the second - has a fence from above. The last option is the most optimal, as it does not take particles of sand, large tractions of garbage. It is practically not clogged.

If in the vibration pump comes from below, this effect is relevant for flushing freshly broken wells. A suspension is driven through the cavity, and the small garbage is easily washed from the remnants of the work.

Material for housing

Early models were produced exclusively from aluminum. Such a housing was easy to maintain, but could be covered by the growths, and also subjected to corrosion processes in separate places.

In the current conditions, manufacturers offer plastic housings. They also behave comfortably when working with water, but are not exposed to rust. The disadvantage of such copies is a significant fragility of cabinet elements.

Varieties of pumps

Depending on the operating conditions, the Aquarius pumps may be superficial, submersible and depth. All pumps have two compartments - pumping and motor. Principle of operation of the working body Vibrating or centrifugal. General requirement - the pump works only in the aquatic environment.

Aquarius surface pumps are installed near the well. The intake hose, it is a suction nozzle, can lift fluid to level up to 9 meters. The condition of work - before starting the suction pipe must be under the bay, so the line requires the installation of the check valve. The pump can pump out clean water from open reservoirs and wells, easily moved, it is inexpensive. The line has 3 models of the BC series, for pumping water to 35 0 C. The unit is not noisy, since a single-phase motor has a low power, the performance is simple, not moisture-proof.

The Aquarius submersible pump is included in the work 10 minutes after lowering the chamber. The unfilled device cannot be included - breakdown is inevitable. The pump is made of engine, a working body, cable, float and discharge pipes. The method of suspension or stationary consolidation. At the same time, the kit should be protection against dry suction and thermostat. The equipment of the NVP series is used. The equipment has less productivity, but not clogged when working on muddy water. Used products of the BCPEU series. Submersible pumps are installed to a depth of 7 m with a capacity of up to 3.8 m 3 / hour. In this case, the cross-section of the casing should be more than 110 mm.

Pumps Vibration NVP can swing a muddy liquid, installed in low-cross-section casing pipes, but they have a smaller working resource. Therefore, users prefer centrifugal devices

If the well is deep, it is necessary to use Aquarius. The well is called a product that has a greater power, and can feed water from the well on sand with the desired pressure. These are centrifugal screws with an elongated working chamber. The models of the BCPE series are installed on the well with a cross section of 120 mm.

Aquarius depth pumps are installed in the artesian well of a large depth. Apply:

centrifugal;
vibrating membrane installations.

Vibration pumps can be installed even in a narrow pipe, since the housing is made with an external cross section of 86 mm. The devices of the BCPE and NVP series have an electrical AC drive with a 220 V network voltage and frequency50Hz. The devices can submit an agent from a depth of 200 m to a height of up to 150 m. Depending on the performance, the weight of the deep pump of Aquarius of the BCPE can reach 17.8 kg and have a linear size up to 2.5 m. The depth mechanisms are equipped with all the necessary automation, the condensate box is carried out beyond the well. When installing the pump is placed at 1.0 - 0.4 m from the bottom of the well to raise the sparkling water.

The centrifugal pump for an aquarium well is available in various modifications. They differ:

capacity;
pressure;
nominal and maximum flow;
the size and number of steps.

The operation of the centrifugal pump provides the engine, from the shaft of which the rotation is transmitted to the blades of the impeller through the hermetic partition. Depending on the purpose, several lifting steps are used, providing the necessary technical parameters.

The membrane apparatus does not have a impeller. The engine and working compartment shares the membrane. Due to the oscillatory movement from the rod, the necessary lifting force is created.

All pumps for pumping clean water The manufacturer performs from neutral materials permitted by standards. Stainless steel, brass, special polymers do not interact with the agent.

Submersible pumps are used more often. They work with constant engine cooling in stable conditions, which increases the motor life. On average, submersible devices operate for 3 years longer surface.

Device, principle of operation and the use of the pump of Aquarius- 3

The equipment operates from a single-phase network, pumps clean water with a temperature not higher than 35 0 C, is used with a depth of immersion of 1-40 meters. The pump can work for 2 hours with a break of 15 minutes. The device is produced with protection against electric shock I, II class.

Aquarius pump - 3 refers to the class of vibration. Hydraulic chamber is a closed pipe space with a suction valve. Due to the vibration produced by a special node, alternately filling the chamber and the release of water into the injection pipeline.

The pump in the casing must be fixed. It is unacceptable to hang it on the feed cable or selection hose. At times, it is necessary to conduct a revision of the design for the abrasion of the protective ring.

Technical characteristics of the Aquarius pump (Lepse):

type - centrifugal, submersible;
productivity - 400 l / h;
power 265 V;
immersion depth - 1-3 m;
mass - 4 kg.

The same Aquarius-3 apparatus is used to pump clean water. The pump is equipped with an automatic thermal block. The starting device is connected to automation. The output fitting has a regulating valve - the flow rate and pressure changes.

Description of the pump BCPE Aquarius for pipe 110 mm

Aquarius 40 pump is installed on casing pipes with a cross section of 110 mm, in marking it is reflected in the presence of a letter of W. Household pump represents a truncated cone. A submersible device is used to pump water from tanks and wells. The engine is applied single-phase, working impeller multistage. The engine is located in the oil compartment, but the ingress of petroleum products into water is excluded by the labyrinth design.

Water consumption is regulated by the shut-off reinforcement on the injection, but the complete overlap of the feed when the pump runs is unacceptable. To overheat the pump can lead the poverty water supply hose into the container. When the engine is disconnected, the protective relay, after cooling the housing, the installation will turn on automatically.

Aquarius technical indicators 0.5-40u:

pressure up to 50 m;
productivity - 1.8 m 3 / hour;
engine power - 1 kW;
exterior case cross section - 104 mm

The voltage drops on the network, scored or laid on the break hose can output the pump. We need to carry out the maintenance of the pump once every 2 years with checking the condition of the salon, cleaning the case, inspecting the working part.

A series of pumps with reduced water consumption.

Aquarius pump 32 is designed for users who do not need high installation performance. This may be caused by the small flow of water into the foster well camera. On the other hand, high consumption for business needs is not needed. Line of the 32 series is extensive. Due to the scope of pressure and applying equipment in deep wells, several models have been created. Traditional good value / quality ratio has expanded with additional complete set. The cable length in the standard configuration is equal to the magnitude of the pressure in meters. The kit comes a kapron cable - the suspension and the condenser block connected to the cable. In this case, the pump of Aquarius is 0.32-140u can supply water from a depth of 150 m.

The advantage of the 32 series is considered:

the ability to operate low flow equipment in nominal mode;
the devices are manufactured taking into account the sanitary standards for contacting the tool with food materials;
there is a thermaller;
sufficient cable length;
low cost product.

The user can easily choose the "Aquarius" brand for pumping water from any tanks and wells with a temperature below 35 0 S. Equipment of this brand has proven itself as a reliable, resistant voltage drops. It is allowed to use some models on obviously turbid water. In Russia, Aquarius pumps are leaders of sales.

The equipment is suitable for repair, spare parts inexpensive, disassemble and assemble the tool with your own hands.